Welcome to the official website of Guangdong Chuangzhi Intellingent Equipment Co.,Ltd.

26 years of experience,thousands of cases

Coating equipment solution integrator

Language
Banner
News

NEWS

NEWS CLASSIFICATION

CONTACT

Chairman
Yan Changzhi
Add

Add:No.2 Yingbin Avenue, High-tech District, Zhaoqing City, Guangdong Province, China.

Location:
Home
/
/
Introduction to the primer process of motorcycle plastic parts coating production line

Details

Introduction to the primer process of motorcycle plastic parts coating production line

  • Categories:News Center
  • Author:Chason
  • Origin:Chuangzhi Painting
  • Time of issue:2020-11-11
  • Views:
  • Share:

(Summary description)Motorcycle plastic parts spraying methods are divided into manual air spraying and automatic spraying. Manual air spraying is one of the more extensive spraying methods in the current motorcycle plastic coating production line.

Introduction to the primer process of motorcycle plastic parts coating production line

(Summary description)Motorcycle plastic parts spraying methods are divided into manual air spraying and automatic spraying. Manual air spraying is one of the more extensive spraying methods in the current motorcycle plastic coating production line.

  • Categories:News Center
  • Author:Chason
  • Origin:Chuangzhi Painting
  • Time of issue:2020-11-11
  • Views:
Information

Motorcycle plastic parts spraying methods are divided into manual air spraying and automatic spraying. Manual air spraying is one of the more extensive spraying methods in the current motorcycle plastic coating production line. This spraying method mainly uses compressed air to remove the paint. After being sucked in from the straw, it is sprayed out through the nozzle to form a paint mist, which is then applied to the surface of the part to form a uniform paint film; automatic spraying generally uses automatic spraying systems such as robots and reciprocating machines, but the one-time investment is relatively large. This method is suitable for higher output Large assembly line production.
Compared with the previous motorcycle plastic parts coating production line, the new primer and topcoat technology has taken tentative steps in terms of energy saving and environmental protection: the spray booth exhaust gas is recycled, and the spray booth only needs to add 20% of the fresh air; in addition, 80% of the air volume is reprocessed by the circulating air in the spray booth and then sent to the spray booth for recycling; new materials are used, and the topcoat uses low-temperature and high-solid paint materials, which can greatly save energy and reduce air pollution.

motorcycle
1. Primer spraying on motorcycle plastic parts coating production line
The more advanced motorcycle plastic parts coating production lines all use robot spraying. The thickness of the primer paint film used by robot spraying is relatively thin, generally no more than 10 µm, and the ability to cover defects of the substrate is weak. This kind of primer generally does not need to be baked, and the topcoat can be sprayed directly after natural leveling for about 15 minutes.
The wind speed in the automatic spray area of ​​the spray booth is controlled at 0.2-0.25 m/s, and the process temperature is generally controlled at 18-35°C. The temperature in the spray booth in winter is generally not lower than 18°C. The wind speed in the manual spray area of ​​the spray booth is generally set at 0.4-0.5 m /s, there is no refrigeration system in the spray booth in summer. You can increase the humidification system to ensure that the temperature of the spray booth in summer is basically controlled below 35℃, the relative humidity is generally controlled at 60%-70%, and the air filter must reach 100,000 (paint booth air Cleanliness requirements> 5μm, the number of particles in the particle size is zero, <5μm, the content of particles in the particle size <1 X 105)
Motorcycle plastic parts coating production line robot spraying uses centralized paint supply, general varnish and primer use two-pipe line system, color paint generally uses 8-10 pipe line system, manual spraying generally uses single-tank paint supply system, paint construction pressure It is generally controlled at 0.2-0.3 MPa, and the atomizing air pressure is generally controlled at 0.5-0.6 MPa. The primer is sprayed in 2 coats, and the second coat is sprayed after the first coat is flashed for 50s, and the film thickness is controlled at 35-40 µm.

coating production line
2. The primer of the motorcycle plastic parts coating production line is leveled and dried
After the primer is sprayed, the wet paint film contains a lot of organic solvents. If it is directly baked in the drying room, the solvent will volatilize too quickly, causing defects such as pinholes and bubbles on the surface of the coating film. During the drying process, along with the volatilization of the solvent, the paint can be fully leveled and unfolded. The drying time and wind speed have a greater influence on the leveling effect, and it is easy to produce paint film defects such as poor leveling and orange peel. The drying time is generally controlled In 3-15min, the wind speed is generally 0.2-0.3 m/s.
3. Primer drying for motorcycle plastic parts coating production line
The primer coatings used for plastic parts are mostly two-component coatings. There are two types of primer coatings currently in use: quick-drying type and ordinary type. The quick-drying type can be dried naturally. At present, most production lines use fast-drying primers. , Generally do not need to bake, spray the top coat directly after 10-15 minutes after spraying. However, the ordinary type cannot be cured naturally and quickly after construction. It is necessary to adopt a heating curing method to shorten the drying time of the coating and improve the coating performance. At the same time, the heat resistance and easy deformation characteristics of the plastic parts should be taken into account. The drying temperature should not be too high. It is generally controlled at about 75℃, and the process time is generally 20-30min.

motorcycle plastic parts
4. Primer polishing for motorcycle plastic parts coating production line
During the primer spraying process, there are more or less paint defects such as particles, sagging, and less paint on the surface. Therefore, after the primer is dried or dried, in order to provide a good paint coating surface for the next process, it is necessary to The surface of the paint parts is polished. The polishing material is generally 600-1000# water sandpaper; for general defects, use 1000# sandpaper; when polishing larger defects, first use 60 ore sandpaper for rough sanding, and then 1 000# fine sandpaper for fine sanding Again.

Keyword:

Scan the QR code to read on your phone

RELATED PRODUCTS

Pre
1

RELATED NEWS

Pre
1
LOGO

It owns Guangdong Chuangzhi Machinery Equipment Co., Ltd., Guangdong Chuangzhi Software Information Technology Co., Ltd., and Hong Kong Chuangzhi Engineering Co., Ltd. has obtained 101 patents in the field of coating equipment and environmental protection equipment. 

CONTACT US

Address:No.2 Yingbin Avenue, High-tech District, Zhaoqing City, Guangdong Province, China.

MESSAGES

留言应用名称:
客户留言
描述:

验证码

Provide customers with all kinds of non-standard coating production lines, coating equipment, environmental protection equipment and other overall solutions. At present, they have been widely recognized in the auto parts industry, furniture industry, musical instrument industry, cookware industry, home appliance industry, hardware industry and other fields. He used to be Honda, BYD, Wuzhou Dragon, Lizhong Wheel, Meishan.   Provide customers with all kinds of non-standard coating production lines, coating equipment, environmental protection equipment and other overall solutions. At present, they have been widely recognized in the auto parts industry, furniture industry, musical instrument industry, cookware industry, home appliance industry, hardware industry and other fields. He used to be Honda, BYD, Wuzhou Dragon, Lizhong Wheel, Meishan.

  Copyright © Guangdong Chuangzhi Intellingent Equipment Co.,Ltd.   粤ICP备17101617号